The multifunction GL200
device accepts inputs form voltage, temperature,
current*, humidity, pulse and logic signals. This
allows combined measurements,
even for disparate phenomena such as temperature/humidity
and voltage.
*External shunt resistor required.
With an isolated input system the
GL200 ensures that cross channel interference is
minimised and this eliminates the need to pay special
attention to wiring.
Accepts USB memory devices of up to 1GB
capacity and allows easy connection to PCs
Two ports
are provided on the GL200, one for the plug-in
USB memory device and one for connecting to a PC.
Commercially available USB memory
devices may be used for direct capture of data or
to transfer
data
to
a PC. With a 512MB
USB memory device, users can capture data for
up to 269
days*. In
addition, the GL200 can be connect directly
to a PC via the USB cable which allows data to be
transferred or measurements to be stored directly
to the PC.
* 10 channels, 1-s sampling rate.
Built-in flash memory for reliable
measurements
The flash memory used for the built-in
memory device ensures that data is retained even
if the power supply is interrupted. This means
momentary disruptions in the AC power supply or
accidentally switching off power will not result
in data loss.
User –friendly
design
The GL200 incorporates
feature such as the ability to set measurement
parameters
for each item separately and navigation assistance
to provide superior operability. The device
case features stylish non-slip rubber.
Vivid 90mm
(3.5") TFT colour LCD
The bright, easy-to-read 3.5-inch
TFT colour LCD monitor makes it even easier
to review
measurement parameter settings, measured
waveforms, and digital values. All
the GL200's functions can be accessed through
the navigation cluster and LCD screen. Single
touch buttons for such tasks as display mode,
setup and logging start/stop negate the need
for complicated menu trees.
6 hours of continuous battery
operations
A convenient optional battery pack
is available for use in areas where AC power
is unavailable
or subject to interruption. The battery pack
enables 6 hours* of continuous measurement
and provides
a remaining battery capacity display function.
* Varies with measurement conditions.
Free
Bundled PC software
The GL200 is bundled with PC
application software that enables measurements
directly with a PC. In addition to waveform
monitoring, this software provides other
useful functions
such as direct writing of data to an Excel
file and report creation. The software
also provides a Help display function for
enhanced
usability.
Software Features
Configuration and channel setup
via USB * Real time data storage to hard disk.
Stored
data import from GL200.
Email notification
of errors and alarms.
Available measurement
modes: Y-T, X-Y, and FFT.
Separate screens
are available for each of the settings.
Direct
Excel transfer can be enabled as a report
function.
GL200 Main Features
Inputs: Voltage (20mv to 50V),
Thermocouples (K,E,J,T,N,R,S,T,B,W) and 4-20mA
signals via external shunt resistor. Optional Graphtec
Humidity sensor is available.
One pulse input and one trigger input.
16-bit ADC resolution.
90mm (3.5") colour LCD
display (320 x 240 pixels).
Waveform and text display modes.
Easy-to-use keypad
menu system.
Single open-collector alarm output.
Range of trigger
functions.
Real-time statistical calculation.
Built-in 3.5M
memory.
2 x USB 2.0 interfaces - one
for USB Memory stick and one for PC connection.
Built-in battery
for up to 6 hour operation.
Scan speed - 0.1s/sec for all
10 channels maximum.
Ultra small
(194mm x 122mm x 41mm).
The GL200 includes the following:
1. GL200 Quick Start Guide.
2.
midi LOGGER Software.
3.
Australian mains cable.
4.
Power Supply - 24Volts DC.
5.
USB Cable*.
6.
BP517 Battery*.
